FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Tojasho Yok
Country: Bulgaria
Language: English (Spanish)
Genre: Medical
Published (Last): 12 January 2010
Pages: 23
PDF File Size: 16.93 Mb
ePub File Size: 6.86 Mb
ISBN: 893-4-46986-237-2
Downloads: 56453
Price: Free* [*Free Regsitration Required]
Uploader: Mautaur

Only one board can be used at any one time, do not try to stack multiple boards. For improved response times use a ‘dummy’ resistor, see the figure below. Associated Manuals The following manuals are recomended as esential reference material for the correct operation of a FX1N series Programmable controller. Circuit protector or fuse? Fix board to base unit using screws C.

Check the output LEDs for operation. This manual provides information for the installation and use of the FX1N. If a high speed response is required, a current of 10 – mA must be used.

C M3 screw to secure top cover. PL E xtension block? Check the previously down loaded program works correctly. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

A standard input X0 to X17 defined by the system parameters. Verify the program to ensure it has been written to the PLC correctly.

Once installation is complete remove the protective paper band, to prevent overheating. D Top cover for board. D, D M Program execution error ref. The value depends on the switch setting.

  MANHATTAN TRANSCRIPTS TSCHUMI PDF

Upper pot, D read from VR1. Remotely from a personal fx1 or other programming peripheral.

AC Wor ld spec. All examples and diagrams shown in this kanual are intended only as an aid to understanding the text, not to guarantee operation. These engineers should also be trained in the use and maintenance of the completed product. See equation 1 for Rb calculation. Circuit protector or Fuse? Remove base unit top cover. Do not remove this screw.

If during the installation of manuzl products or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site.

Mitsubishi FX1N-24MT-ESS/UL Manuals

D, D M Program circuit error ref. Software warning 4 Indicates special care must be taken when using this element of software. Take special care not to allow debris to fall inside the unit during installation e. Low voltage cables should be reliably separated or insulated with regard to high voltage cabling. It should be read and understood before attempting to install or use the unit.

Ground resistance must be less than ? Input circuit power supply? Each of the symbols used will now be listed with a brief description of its hzrdware. Grounding is recommended but if a proper ground cannot be provided, the PLC will still hardqare correctly without being grounded. Units should not be installed in areas subject to the following conditions: All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams.

All maintenance should be carried out in accordance with established safety practices.

  INTRALOX CATALOGO PDF

Mitsubishi FX1NMT-DSS Manuals

This manual is subject to change without notice. LED is lit B Check for programming error. When the products associated with this manual are used as a system or individually, they must be installed in a suitable enclosure. Never mount them to the floor or ceiling of an enclosure. See equation 2 for Rb calculation. If during the installation of these product or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site.

Mechanical interlocks MUST be fitted to all safety critical circuits. Terminals screws should be tightened to between 0.

For greater detail, specifications and wiring examples for each optional unit, please see the relevant product manuals. However Additional extension blocks can be powered from the main unit power supply 4.

Check the power LED is lit. During this testing stage take extreme care not to touch any live or hazardous parts.

Mitsubishi FX1N-24MT-DSS Manuals

Parallel LED Eqn 1: The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. Note that the ground cable must not be connected to the same ground as the power circuits. Haardware a response time of 0. E M3 screw to secure top cover.