The CF Development Kit is intended as a development platform for the Refer to the CF93x-CF92x data sheet for the differences between. Explore the latest datasheets, compare past datasheet revisions, and confirm part lifecycle. Buy SILICON LABS CFGQ online at Newark element Buy your Technical Datasheet: CFGQ Datasheet. See all Technical Docs. X. X.
|Published (Last):||9 May 2004|
|PDF File Size:||6.96 Mb|
|ePub File Size:||17.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Prev Next CF D. Add pre-defined groups or add customized groups. This kit comes with the CF microcontroller installed—see Figure 1 below. Select files to be added. Figure 10 below is a screen shot of said analyzer with the correct configuration. The information in this document is believed to be accurate in all respects at the time of publication but c8051t930 subject to change without notice. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information.
Two touch sensitive contactless switches are provided on the target board. CFTB datasheet and specification datasheet Download datasheet. Figure 9 on page 14 shows the factory default shorting block positions The header J6 provides access to the ground plane for easy clipping of oscilloscope probes. Source code examples and register dataseet files.
Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including but not limited to nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Elcodis is a trademark of Elcodis Company Ltd.
This pin is the external daatasheet input in capacitor or RC oscillator configurations. In-system Flash memory programming integrated into the driver allows for rapid updating of target code. In dual-cell battery mode, this pin must be connected directly to ground. Keil Assembler and Linker The Keil demonstration toolset assembler and linker place no restrictions on code size.
CFTB Silicon Laboratories Inc, CFTB Datasheet
LED flood light qty 2. The code excerpt below shows the necessary code changes. Factory Defaults 14 P This pin is the external clock input in external CMOS clock mode. Trademark Information Silicon Laboratories Inc. This pin is the external oscillator return for a crystal or resonator. Silicon Laboratories products are generally not intended for military applications. datasheeg
C8051F930-GM 8051 8-bit Microcontroller
Below are some suggestions for reducing the active supply current: Configuration Wizard 2 Utility The Configuration Wizard utility helps accelerate development by automatically generating initialization source code to configure and enable the on-chip resources needed by most design projects This project uses a C microcontroller development kit, an accelerometer evaluation board, and Simplicity Studio IDE—all from Silicon Labs—to rather quickly and easily build a motion-detecting alarm system. This supply voltage is not required in dtasheet power sleep mode.
V are selected when SW4 is configured to two-cell mode. The audio piezo alarm chosen for this project is a slow warble alarm with a resonant frequency range of to Hz.
Register 0x32 sets the acceleration threshold set to mg for when the Int1 signal datqsheet driven; the mg threshold setting c8051f9330 what makes the motion detector so sensitive to slight accelerations. The alarm and the lights will stay energized until the microcontroller is reset. This pin can only be used as GPIO.
The CF Development Kit is intended as a development platform for the microcontrollers in the. Factory Defaults The CF target board comes from the factory with pre-installed shorting blocks on many headers.
However, instead of referencing “Clock Phase” and “Clock Polarity”—which seems to be the norm see section If the power supply ramp takes longer than reach 0. Alternatively, a shorting block can be placed on J17 to ensure that the multimeter does not limit current during startup. Copy your embed code and put on your site: Windows will automatically finish the driver installation. Initial response time for FA requests that meet this requirements will follow the standard FA guidelines for packaged parts.
Target Board Shorting Blocks: The capacitors are connected to P0. This alarm has its own internally driven circuitry and operates from 5V to 15V, which is perfect for this project because we have 12V readily available.
Figure 9 shows the positions of the factory default shorting blocks. After you run the code, lightly tapping the accelerometer evaluation board or the breadboard should sound the alarm and turn on the two LED flood lights.
Right-click on the group name and choose Add file to group. The CF Development Kit contains the following items:.