L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked _机械 /仪表_工程科技_专业资料。ASTM A Standard.
|Published (Last):||20 February 2009|
|PDF File Size:||5.42 Mb|
|ePub File Size:||20.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
This abstract is a brief summary of the aetm standard. They shall be formed in different shapes such as sheets, strips, plates and flat bars. This standard has been approved for use by agencies of the Department of Defense. Hard Elongation in 2 in. Historical Version s – view previous versions of standard.
The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The values given in parentheses are for information only.
The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.
Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.
ASTM A Standard Specification for Annealed or Cold-Worked_百度文库
Rockwell B 95 95 This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? C Annealed material that naturally meets mechanical properties may be applied. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. However, in the case of dispute, tests shall be made by pressure. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?
Last previous edition approved in as A — Specimens shall be a66 around a diameter equal to the product of the bend factor times the speci? D PSS means plate, strip, sheet. Your comments will receive careful consideration at a meeting of the responsible technical s666, which you may attend.
The noncontrolling factor normally will exceed considerably the speci?
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
HardC Elongation in 2 in. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
A — 03 Standard Speci? A number in parentheses indicates the asgm of last reapproval. Material Test Report and Certi? An alternative method of determining? Current edition approved Oct. Link to Active This link will always route to the current Active version of the standard. In case of dispute, the offset method of determining yield strength shall be used.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The steels shall adhere to specified chemical composition requirements. The values given in parentheses are for information only.
This revision of Speci? Originally approved in The choice of test method for materials in conditions other than annealed shall be at the option of the seller. B Maximum unless otherwise z666.
This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
Number of Tests 8.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
ICS Number Code Only annealed conditions of grades speci?
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. One bend w666 shall be made from one end of each coil. A superscript epsilon e indicates an editorial change since the last revision or reapproval.